Questions an interviewer could realistically ask about this project, drawn from
../component-selection.md,
../schematic-notes.md,
../kicad-walkthrough.md and
../documentation.md.
A multi-radio IoT gateway board: ESP32-C6 MCU, SX1262 LoRa, SIM7080G cellular, W5500 Ethernet with
PoE, USB-C, microSD — designed in KiCad.
This is the only hardware project in the vault, which makes it disproportionately memorable in a
software interview and essential to know cold in a hardware or embedded one.
How to use this
- Answer out loud, from memory, before reading the hint.
- Strong answer covers = the checklist a good answer hits, not a script.
- [Beginner] / [Intermediate] / [Advanced] = how much project context the question assumes.
- 🔥 = most likely to be asked.
Files
| File | Covers |
|---|---|
| 01-architecture-and-components.md | Why each part was chosen, the alternatives rejected, radio/interface trade-offs |
| 02-power-and-rf.md | PoE, ORing auto-switch, regulation, rail separation, the RF switch, antenna/magnetics |
| 03-schematic-workflow-and-story.md | KiCad process, ERC, PWR_FLAG, what’s left, trade-offs, behavioural |
Before anything else: the 60-second pitch
It’s an IoT bridge board — a gateway that collects from local devices over LoRa, Zigbee or Thread
and backhauls over whichever link is available: Ethernet with PoE, cellular, or Wi-Fi. ESP32-C6 as
the MCU because its 802.15.4 radio gives Zigbee and Thread alongside Wi-Fi 6 on one chip, SX1262
for LoRa at 868 MHz since Nigeria is ITU Region 1, SIM7080G for LTE-M/NB-IoT with 2G fallback, and
a W5500 for Ethernet because it’s a hardwired TCP/IP stack rather than a raw MAC — the ESP32
doesn’t have to run a software stack for it. The decisions I’d defend hardest are on the power
side: three inputs — PoE, USB-C and a barrel jack — auto-switched with ORing ideal-diode
controllers, and a separate 3.8V LDO for the cellular modem specifically so its transmit
current spikes can’t sag the 3.3V rail everything sensitive runs on.
The cellular rail separation is the line to lead with — it’s the decision that shows you understand
what actually kills mixed-signal boards.
Key parts (memorise this table)
| Function | Part | One-line reason |
|---|---|---|
| MCU | ESP32-C6-WROOM-1-N8 (module) | Wi-Fi 6 + BLE + 802.15.4 (Zigbee/Thread) on one RISC-V chip; module = pre-certified RF |
| LoRa | Semtech SX1262 | 150–960 MHz, +22 dBm TX, –148 dBm sensitivity, <1.5 µA sleep |
| RF switch | Skyworks PE4259 | SPDT; SX1262 has separate TX/RX ports, one antenna |
| Cellular | SIMCom SIM7080G | LTE-M + NB-IoT + EGPRS fallback, GNSS bonus, UART/AT |
| Ethernet | WIZnet W5500 | Hardwired TCP/IP, 8 sockets, SPI to MCU |
| PoE | TI PPS23730A0RMTT | 802.3af/at with integrated DC-DC controller |
| Power ORing | TI LM66100 ×2 | Ideal-diode auto-switching between sources |
| 3.3V rail | TI TLV1117-33 LDO | 800 mA, SOT-223 |
| 3.8V rail | Separate LDO | Isolates cellular current spikes |
| RJ45 | HR911105A MagJack | Integrated magnetics — no separate transformer |
Software engineering
Infrastructure & security
Computer science
Hardware & engineering