IT Consortium Logo

Project Title: Universal IoT Bridge PCB Design
Author: Kingsley Ihemelandu
Organisation: IT Consortium
Department: Research Department
Date: June 2026
Revision: v0.1 — Schematic Phase
Status: Schematic substantially complete — PCB layout and PoE controller wiring outstanding


Abstract

This report documents the design of a universal IoT Bridge printed circuit board (PCB) intended to serve as a central communication hub for IoT edge device deployments. The bridge is designed to support simultaneous operation across multiple wireless protocols — including Wi-Fi 6, Bluetooth 5 Low Energy, Zigbee 3.0, Thread 1.3, LoRa, and cellular (LTE Cat-M1 / NB-IoT) — while providing wired Ethernet connectivity with Power over Ethernet (PoE) support.

The design is exploratory in nature, with the objective of validating component compatibility, feature integration, and PCB layout strategies before a production version is finalised. This document covers the component selection rationale, system architecture, design decisions made during the schematic phase, and the tools used throughout the design process. Elements of this design may be adapted, refined, or omitted in a subsequent production revision.


Table of Contents

  1. Project Overview
  2. System Architecture
  3. Component Selection
  4. Design Decisions
  5. Tools & Software
  6. Schematic Progress
  7. Work Completed
  8. Outstanding Work
  9. KiCad Familiarisation
  10. Deliverables
  11. Project Repository
  12. References

1. Project Overview

1.1 Background

IoT deployments increasingly require a single gateway device capable of communicating with heterogeneous edge nodes — sensors, actuators, and smart devices that speak different wireless protocols. A device that can bridge LoRa sensor nodes, Zigbee smart home devices, BLE peripherals, and Thread/Matter devices simultaneously — while maintaining cloud connectivity over Ethernet or cellular — represents significant value in both commercial and industrial IoT applications.

1.2 Objectives

  • Design a PCB that integrates the major IoT wireless protocols into a single device
  • Support dual power inputs (PoE and USB-C) with automatic failover
  • Provide both local storage (MicroSD) and over-the-air (OTA) firmware update capability
  • Ensure the design is modular and maintainable, with clear documentation to guide a potential production revision

1.3 Scope

This design is a feature exploration prototype. It is not intended for immediate mass production. The scope covers schematic design, component selection, PCB layout, and generation of manufacturing files (Gerbers, BOM).

1.4 Key Features

FeatureImplementation
Wi-Fi 6 (802.11ax)ESP32-C6-WROOM-1 (built-in)
Bluetooth 5 LEESP32-C6-WROOM-1 (built-in)
Zigbee 3.0ESP32-C6-WROOM-1 (built-in, 802.15.4 radio)
Thread 1.3 / MatterESP32-C6-WROOM-1 (built-in, shared 802.15.4 radio)
LoRa (hub + LoRaWAN end-node)Semtech SX1262
Cellular (LTE Cat-M1 / NB-IoT)SIMCom SIM7080G
GNSS / GPSSIM7080G (built-in)
Wired Ethernet (10/100)WIZnet W5500
Power over EthernetTI PPS23730A0RMTT
USB-C (power + programming)Native ESP32-C6 USB Serial/JTAG
Flash Storage8MB on-module (ESP32-C6-WROOM-1-N8)
Removable StorageMicroSD card slot (SPI)
Status IndicatorRGB LED
User InputTactile push button

2. System Architecture

2.1 Block Diagram

                    ┌──────────────────────────────────────────────────┐
                    │          ESP32-C6-WROOM-1 (Main MCU)             │
                    │                                                  │
                    │   Wi-Fi 6 | BT 5 LE | Zigbee 3.0 | Thread 1.3    │
                    │                                                  │
   SX1262 ◄─ SPI ──►│  SPI Bus                                         │
   W5500  ◄─ SPI ──►│  (shared MOSI/MISO/SCK, individual CS lines)     │
   MicroSD◄─ SPI ──►│                                                  │
                    │  UART ─────────────────────────────► SIM7080G    │
                    │  USB D+/D- ────────────────────────► USB-C Port  │
                    └──────────────────────────────────────────────────┘
                              │                    │
                          +3V3 rail            +3V8 rail
                              │                    │
                       TLV1117-33           AP2112K-3.8
                              └──────┬─────────────┘
                                     │
                               +5V system rail
                                     │
                      ┌──────────────┴──────────────┐
                      │                             │
                 LM66100 #1                    LM66100 #2
                      │                             │
             PPS23730A0RMTT (PoE)          USB-C VBUS (5V)
                      │
             RJ45 + Magnetics
             (PoE 48V input)

Antennas (all via U.FL connectors on enclosure exterior):
  ESP32-C6  ── 2.4 GHz   (Wi-Fi / BT / Zigbee / Thread)
  SX1262    ── 868 MHz    (LoRa — Region 1)
  SIM7080G  ── LTE        (Cellular)
  SIM7080G  ── GNSS       (GPS/GLONASS — separate port)

2.2 Power Architecture

The board supports two independent power inputs that are automatically OR’d together using ideal diode controllers:

  • PoE input: 48V from Ethernet cable → TPS23730 PD controller → 5V regulated
  • USB-C input: 5V from USB connector

Both 5V sources feed into a pair of LM66100 ideal diode controllers. The higher of the two voltages supplies the system rail automatically, with no manual switching required and no risk of reverse current damage.

From the 5V system rail, two voltage regulators produce the required supply voltages:

  • 3.3V (TLV1117-33): Powers the ESP32-C6, W5500, SX1262, and MicroSD
  • 3.8V (AP2112K-3.8): Powers the SIM7080G exclusively (isolated to prevent cellular noise from affecting other components)

3. Component Selection

3.1 Rationale Summary

ComponentSelected PartKey Justification
MCUESP32-C6-WROOM-1-N8Only ESP32 variant with 802.15.4 (Zigbee + Thread) + Wi-Fi 6 + BT5 in one chip
LoRa TransceiverSemtech SX1262Current-generation chip; −148 dBm sensitivity; same chip inside RYLR998 module
CellularSIMCom SIM7080GLTE Cat-M1 + NB-IoT + GNSS; correct IoT tier; 2G fallback
Ethernet ControllerWIZnet W5500Hardwired TCP/IP stack; SPI interface; well-supported in ESP-IDF
PoE ControllerTI PPS23730A0RMTTPoE PD controller with integrated DC-DC; same TPS23730 family; 47-pin; found in KiCad library
LoRa RF SwitchSkyworks PE4259SPDT RF switch routing single antenna between SX1262 TX and RX paths; controlled by DIO2
Power OR’ingTI LM66100 ×2Ideal diode OR’ing; near-zero voltage drop
3.3V RegulatorTLV1117-33Low-noise LDO; sufficient for all 3.3V loads
3.8V RegulatorAP2112K-3.8Dedicated isolated supply for cellular module

Full component research, alternative options considered, and detailed justifications are documented in component-selection.md.


4. Design Decisions

DecisionChoice MadeRationale
MCU module vs bare chipWROOM-1 moduleIntegrated antenna matching, decoupling, and FCC certification simplify design
LoRa frequency band868 MHzNigeria is ITU Region 1 — same band as Europe
Zigbee vs ThreadFirmware-selectableBoth share the 802.15.4 radio; one active at a time based on deployment
USB-C power mode5V default (900mA)5.1kΩ CC resistors only; no USB PD controller needed for this use case
External flashNone addedESP32-C6-WROOM-1-N8 has 8MB on-module — sufficient for dual OTA + filesystem
eSIMDNP footprintSIM7080G has no eSIM; pads reserved for future revision
SPI bus speed16 MHz maxSX1262 is the limiting device at 16 MHz; W5500 and SD card configured to match
Cellular supplySeparate 3.8V LDOIsolates high current-spike cellular transmissions from sensitive 3.3V rail
LoRa antenna switchingPE4259 RF switchSX1262 has separate TX (RFO) and RX (RFI_N/RFI_P) ports; PE4259 routes single antenna between them. DIO2 controls it automatically
W5500 RJ45HR911105A MagJackIntegrated magnetics — no separate transformer needed. Centre tap to +3V3 via 49.9Ω resistor per datasheet
PWR_FLAG usageOnly on externally-sourced netsNets with LDO VOUT pins do not need PWR_FLAG. Only USB_VBUS (from cable) and POE_5V (PPS23730 not yet wired) require it

5. Tools & Software

5.1 PCB Design

KiCad 8.x — Open-source PCB design suite used for schematic capture and PCB layout.

  • Schematic Editor (Eeschema): Draws the logical connections between all components
  • PCB Editor (Pcbnew): Physical placement and copper routing
  • Footprint Editor: Creating/editing component pad patterns
  • Gerber Viewer: Verifying manufacturing files before submission

Espressif KiCad Libraries — Official symbol and footprint library from Espressif for all ESP32 components. Downloaded from the Espressif GitHub repository and added to KiCad’s symbol library manager.

Component Libraries Used in KiCad:

  • Device — standard passive components (resistors, capacitors)
  • Connector — USB-C, RJ45, headers
  • Switch — tactile push buttons (SW_Push)
  • espressif — ESP32-C6-WROOM-1 symbol and footprint
  • power — power symbols (+3V3, GND, +5V, PWR_FLAG)

5.2 Planned Firmware Tools

ToolPurpose
ESP-IDFEspressif’s official C/C++ development framework for ESP32. Provides FreeRTOS, WiFi/BT stack, GPIO drivers, SPI/UART/I2C APIs
FreeRTOSReal-time operating system built into ESP-IDF. Manages concurrent tasks (reading LoRa while serving MQTT while checking Ethernet)
RadioLibArduino/ESP-IDF library for controlling the SX1262 LoRa transceiver over SPI. Supports both raw LoRa and LoRaWAN
LwIPLightweight TCP/IP stack used within ESP-IDF for network communication
ESP-MQTTMQTT client library built into ESP-IDF for publishing sensor data to a broker

5.3 Reference Materials Used

DocumentSourceUsed For
ESP32-C6 DatasheetEspressif (espressif.com)Pin definitions, power requirements, GPIO capabilities
ESP32-C6-WROOM-1 DatasheetEspressifModule pinout, antenna design, footprint dimensions
SX1262 DatasheetSemtechSPI wiring, RF matching network, LoRa parameters
PPS23730A0RMTT DatasheetTexas InstrumentsPoE PD + DC-DC application circuit, transformer selection
PE4259 DatasheetSkyworks SolutionsRF switch wiring, CTRL/VDD supply, truth table
HR911105A DatasheetHanrun / BothhandMagJack RJ45 pinout, centre tap wiring, integrated magnetics
W5500 DatasheetWIZnetSPI interface, crystal requirements, RJ45 wiring
SIM7080G Hardware GuideSIMComPower supply requirements, antenna connections, AT command interface
Heltec WiFi LoRa 32 V3 SchematicHeltecReference for ESP32 + SX1262 integration
AN4488 Application NoteSTMicroelectronicsGeneral hardware design best practices (used as reference)

6. Schematic Progress

SectionStatusNotes
ESP32-C6 MCUComplete3V3 + decoupling caps ✓, EN circuit ✓, BOOT circuit ✓, all GPIO net labels placed ✓, unused pins no-connect ✓
Power — USB-C ConnectorCompleteVBUS → polyfuse → USB_VBUS ✓, CC1/CC2 → 5.1kΩ → GND ✓, D+/D- labeled ✓
Power — OR’ing (LM66100 × 2)CompleteLM66100 #1 (USB path) ✓, LM66100 #2 (PoE path) ✓, both VOUT → +5V ✓, CE → GND ✓
Power — TLV1117-33 (3.3V LDO)CompleteVIN → +5V, VOUT → +3V3, decoupling caps ✓
Power — AP2112K-3.8 (3.8V LDO)CompleteVIN → +5V, VOUT → +3V8, EN → +5V, decoupling caps ✓
Power — PPS23730A0RMTT (PoE)Placed, not wiredAll pins no-connect. Wire last using datasheet application circuit.
SX1262 LoRa TransceiverCompleteSPI/control pins ✓, power pins ✓, crystal (32 MHz, 10pF caps) ✓, PE4259 RF switch wired ✓, Conn_Coaxial (U.FL) ✓, RF matching network pending (copy from datasheet 14.6.2)
W5500 Ethernet ControllerIn ProgressSPI/control ✓, PMODE → +3V3 ✓, EXRES1 → 12.4kΩ ✓, VBG/TOCAP/1V2O caps ✓, crystal (25 MHz, 20pF caps) ✓, RJ45 HR911105A wiring in progress
SIM7080G Cellular ModuleIn ProgressVBAT → +3V8 ✓, UART wired ✓, PWRKEY ✓, SIM card connected ✓, antenna U.FL connectors placed ✓, unused pins no-connect in progress
MicroSD SlotCompleteSPI mode pin mapping applied, pull-up resistors on signal lines ✓
User Interface (Button + LED)CompleteSW_Push with pull-up + debounce cap ✓, LED with 330Ω resistor ✓
Debug Header (UART 4-pin)CompleteConn_01x04 with +3V3, UART_TX, UART_RX, GND ✓
ERCIn Progress2 remaining errors: USB_VBUS needs PWR_FLAG, LM66100 OR-ing conflict to exclude

7. Work Completed

The following schematic sections were fully designed during this internship:

Schematic Design

  • ESP32-C6 MCU — power pins, decoupling capacitors, EN/reset circuit (10kΩ pull-up + 100nF), BOOT circuit (10kΩ pull-down + button), all GPIO net labels assigned, unused pins marked no-connect
  • USB-C Connector — VBUS through 500mA polyfuse, CC1/CC2 pull-down resistors (5.1kΩ) for 5V/900mA negotiation, D+/D- routed to ESP32
  • Power OR-ing (LM66100 × 2) — ideal diode OR-ing of USB-C and PoE 5V sources onto shared +5V system rail; CE pins tied to GND (active-low enable)
  • 3.3V LDO (TLV1117-33) — input and output decoupling caps; supplies ESP32-C6, W5500, SX1262, MicroSD
  • 3.8V LDO (AP2112K-3.8) — isolated cellular supply; EN tied to +5V; supplies SIM7080G exclusively
  • SX1262 LoRa Transceiver — all SPI/control pins wired, power pins with decoupling, 32 MHz crystal with 10pF load caps, PE4259 RF switch for TX/RX antenna routing (DIO2 → 100Ω → CTRL), RF matching network (values from datasheet section 14.6.2), U.FL coaxial connector for LoRa antenna
  • W5500 Ethernet Controller — SPI bus and control pins, PMODE pins for auto-negotiation, EXRES1 (12.4kΩ), internal voltage output decoupling (VBG/TOCAP/1V2O), 25 MHz crystal with 20pF load caps, HR911105A MagJack with differential pair connections and centre-tap resistors
  • SIM7080G Cellular Module — VBAT to dedicated +3V8 rail with bulk capacitors, UART to ESP32, PWRKEY, SIM card holder (VCC, RST, CLK, DATA, GND), two U.FL connectors (LTE antenna, GNSS antenna), unused pins no-connect
  • MicroSD Slot — SPI mode pin mapping, 10kΩ pull-ups on signal lines, VDD decoupling
  • User Button — pull-up resistor with debounce capacitor
  • Status LED — 330Ω current-limiting resistor, anode to GPIO, cathode to GND
  • Debug Header — 4-pin UART header (3V3, TX, RX, GND)
  • PPS23730A0RMTT PoE Controller — symbol placed on schematic, all pins temporarily no-connect (see Outstanding Work)

Component Selection & Research

  • Evaluated and justified all major IC choices (documented in component-selection.md)
  • Identified correct LoRa frequency band for Nigeria (868 MHz — ITU Region 1)
  • Selected HR911105A MagJack to eliminate need for separate Ethernet transformer
  • Identified PPS23730A0RMTT as available KiCad substitute for TPS23730

Design Documentation

  • Maintained schematic-notes.md with all wiring decisions and pin-level connections
  • Maintained learning.md with explanations of every concept encountered
  • Maintained component-selection.md with full justification for every major part

8. Outstanding Work

The following items remain incomplete at the end of the internship period:

Phase 1 — Complete the Schematic

ItemReason incompleteEstimated effort
PPS23730A0RMTT PoE controller wiring47-pin device requiring external transformer, MOSFET, feedback network, and compensation components. Requires datasheet application circuit to be copied exactly — significantly more complex than any other section. Left last intentionally.3–5 hours with datasheet open
SX1262 RF matching network valuesComponent values (inductors and capacitors between SX1262 and PE4259) must be copied from SX1262 datasheet section 14.6.2.1 hour
ERC clean to 0 errorsCurrently 2 remaining: USB_VBUS needs PWR_FLAG; LM66100 OR-ing “two power outputs” to be excluded.15 minutes

Phase 2 — PCB Layout

This is a full separate phase of work that follows schematic completion. It involves transitioning from the logical schematic into a physical board design.

ItemNotes
Assign footprintsEach schematic symbol needs a matching PCB footprint (physical pad size and spacing). Every component must be linked to a footprint before layout can begin.
Component placementPhysically arrange all components on the board. Key considerations: RF components (SX1262, antennas) need separation from digital logic; SIM7080G needs isolation from the 3.3V rail; decoupling caps must be within 1–2mm of their IC’s power pin.
Copper routingDraw actual copper traces connecting all components as defined in the schematic. High-speed signals (SPI, Ethernet differential pairs) need controlled impedance and length matching.
Ground plane pourFill unused copper area with a GND pour for noise reduction and improved RF performance.
DRC (Design Rule Check)Verify no trace clearance violations, missing connections, or manufacturing rule failures.
Generate BOMBill of Materials — exported from KiCad. Lists every component with reference designator, value, part number, and quantity for procurement.
Generate Gerber filesManufacturing output files (one per copper layer, silkscreen, solder mask, drill file) sent to PCB fabrication house (e.g. JLCPCB, PCBWay).

9. KiCad Familiarisation

Prior to starting the IoT Bridge PCB project, time was spent learning KiCad from scratch through tutorial projects and video resources.

Learning Resources Used

ResourceTopicLink
[KiCad 9 Hardware Design Tutorial (TI MSPM0) (1/2 Schematic) - Phil’s Lab]KiCad basics — schematic captureYouTube link
[KiCad 9 Hardware Design Tutorial (TI MSPM0) (2/2 PCB) - Phil’s Lab]PCB layout and routingYouTube link

Concepts Learned During Familiarisation

  • Schematic capture: placing symbols, drawing wires, net labels, power symbols
  • Component libraries: adding external libraries (Espressif, SnapEDA downloads)
  • ERC (Electrical Rules Checker): reading and resolving errors
  • Footprint assignment: linking schematic symbols to PCB pad patterns
  • PCB editor basics: component placement, trace routing
  • KiCad project file structure: .kicad_sch, .kicad_pcb, .kicad_pro

10. Deliverables

  • Component Selection Document (see component-selection.md)
  • Block Diagram (complete — Section 2.1)
  • Schematic — substantially complete (PoE controller wiring and RF matching network values outstanding — see Section 8)
  • PCB Layout — not started (requires schematic completion first — see Section 8, Phase 2)
  • Bill of Materials — not started (exported from KiCad after layout)
  • Gerber Files — not started (generated after layout and DRC pass)

11. Project Repository

All design documentation, notes, and learning resources for this project are maintained in the following GitHub repository:

GitHub: https://github.com/kingsleydaprime/knowledgebase/tree/main/projects/iot-bridge-pcb

The repository includes:

  • documentation.md — this design report
  • component-selection.md — full component research and justification
  • schematic-notes.md — pin-level wiring decisions and gotchas
  • learning.md — concepts learned throughout the project

12. References

  • Espressif Systems. ESP32-C6 Series Datasheet. espressif.com
  • Espressif Systems. ESP32-C6-WROOM-1 Datasheet. espressif.com
  • Semtech Corporation. SX1261/2 Datasheet Rev. 1.2. semtech.com
  • SIMCom Wireless Solutions. SIM7080G Hardware Design. simcom.com
  • WIZnet Co. Ltd. W5500 Datasheet V1.1.0. wiznet.io
  • Texas Instruments. PPS23730A0RMTT Datasheet. ti.com
  • Skyworks Solutions. PE4259 Datasheet. skyworksinc.com
  • Texas Instruments. LM66100 Datasheet. ti.com
  • Heltec Automation. WiFi LoRa 32 V3 Schematic. heltec.org
  • STMicroelectronics. AN4488 — Getting Started with STM32 Hardware Development. st.com
↑ Back to Projects — Learning Logs