RHCSA V10

Part of RHCSA V10. RHEL’s firewall stack — where Ubuntu/Debian notes in this vault use ufw (see Networking Fundamentals), RHEL uses firewalld. The actual kernel-level packet filter underneath is nftables — the modern successor to the older iptables/ip6tables (still convertible via iptables-translate) — and firewalld is the recommended, higher-level front end to it; you almost never touch nftables rules directly.


firewalld vs. ufw — the mental model shift

ufw is dead simple: allow/deny by port or service, done. firewalld adds a layer of zones — named trust levels an interface belongs to, each with its own independent rule set. The idea is a laptop’s wifi interface (untrusted network) and a server’s internal NIC (trusted network) can have completely different rules without juggling one flat rule list.

sudo systemctl status firewalld       # confirm it's running — it is, by default, on RHEL
sudo firewall-cmd --state              # quick running/not-running check

Zones

Every zone allows return traffic for connections you initiated, and all outbound traffic, by default — the table below is specifically what’s allowed inbound, unsolicited:

ZoneDefault inbound behavior
trustedAccept everything
home / internalReject unless related to outbound traffic, or matches ssh, mdns, ipp-client, samba-client, dhcpv6-client
workSame idea, narrower list: ssh, ipp-client, dhcpv6-client
publicDefault zone for newly added interfaces — narrower still: just ssh, dhcpv6-client
externalJust ssh — plus masquerades (NAT) outgoing IPv4 traffic forwarded through it, for a router-like box
dmzJust ssh — publicly reachable, but isolated from the rest of the internal network
blockReject all incoming (not just unmatched)
dropDrop all incoming silently — doesn’t even send back an ICMP rejection, unlike block

Which zone a packet actually lands in is decided in this order: source IP’s assigned zone (if you’ve explicitly bound an address/range to a zone) → the zone of the interface it arrived on → the default zone as a last resort. NetworkManager can also auto-switch a connection’s zone based on which network you’ve joined — the practical payoff is a laptop that’s home-zoned on your home Wi-Fi (SSH reachable) and automatically drops to something tighter on a coffee-shop network, without you touching firewalld by hand.

firewall-cmd --get-default-zone            # which zone new interfaces get by default
firewall-cmd --get-active-zones            # zones currently in use, and which interface is in each
firewall-cmd --zone=public --change-interface=eth0    # move an interface to a specific zone

Runtime vs. permanent — the single biggest gotcha

This mirrors the exact trap that shows up in manage-selinux-security with setsebool -P. firewall-cmd changes are runtime-only by default — they vanish on the next --reload or reboot unless you also write them to the permanent config.

sudo firewall-cmd --add-service=http                      # runtime only — works right now, GONE after reload/reboot
sudo firewall-cmd --add-service=http --permanent           # written to config — does NOT apply until reloaded
sudo firewall-cmd --reload                                  # apply permanent changes to the running firewall

The safe habit: do both together, so runtime state and permanent config never drift apart:

sudo firewall-cmd --add-service=http --permanent && sudo firewall-cmd --reload

Core commands

$ firewall-cmd --list-all
public (active)
  target: default
  interfaces: eth0
  services: cockpit dhcpv6-client ssh
  ports: 8080/tcp

Reading this: public is which zone this is; services are allowed by name (self-documenting); ports are raw port allows that don’t have a named service. This is the single command to run first whenever “is X actually open?” comes up.

firewall-cmd --list-all                       # full ruleset for the DEFAULT zone
firewall-cmd --zone=public --list-all          # full ruleset for a SPECIFIC zone
firewall-cmd --get-services                    # every named service firewalld knows how to allow by name
firewall-cmd --add-service=ssh --permanent     # allow by service NAME — firewalld maps this to the right port(s) internally
firewall-cmd --add-port=8080/tcp --permanent   # allow by raw port — for anything without a named service definition
firewall-cmd --remove-service=http --permanent # revoke
firewall-cmd --list-services                   # just the allowed services, for the default/current zone
firewall-cmd --list-ports                       # just the allowed raw ports

Prefer --add-service over --add-port whenever a named service exists — it’s self-documenting (--list-all shows ssh instead of an unlabeled 22/tcp) and some services need more than one port, which the service definition already accounts for.


Rich rules — when zone/service granularity isn’t enough

For anything more specific than “allow this service in this zone” — like restricting a port to a single source IP:

firewall-cmd --add-rich-rule='rule family="ipv4" source address="192.168.1.50" port port="3306" protocol="tcp" accept' --permanent
firewall-cmd --reload

Worth knowing this exists; the exam mostly stays at the service/port level.


SSH hardening — where this connects back

Changing SSH off the default port (covered in Basic SSH Config) is a two-system change, not one — this is a real trap:

  1. Update Port in /etc/ssh/sshd_config, restart sshd
  2. firewalld — the new port needs an explicit allow, the old one should be removed:
    firewall-cmd --add-port=2222/tcp --permanent
    firewall-cmd --remove-service=ssh --permanent
    firewall-cmd --reload
  3. SELinux — SSH’s default policy only expects sshd_t to bind port 22. A custom port needs its own label or SELinux blocks sshd from even binding it, regardless of what the firewall allows:
    sudo semanage port -a -t ssh_port_t -p tcp 2222

All three layers — sshd config, firewalld, SELinux — have to agree, or the service either won’t start, won’t be reachable, or will bind but get silently blocked. This three-layer check is worth running through as a checklist any time “the service should be listening but isn’t reachable.”

↑ Back to Red Hat Certified System Administrator (RHCSA) V10